SWLCAT Climbing 4-6 Practice Test

These questions are part of the practice quiz. Start practicing

• Avoid rubbing fall protection equipment on which surfaces?
• If the pole is NOT in good shape, should two workers climb or descend a pole at the same time?
• If the pole is in good shape, two people can climb or descend a pole at the same time.
• When working from an aerial lift, which protection must be used?
• With a work positioning system, a worker can fall
• Which technique helps prevent rope drag when moving along a traverse?
• A safety strap is normally twisted in order to give it a better grip on slippery poles.
• Who is identified as responsible for sharpening and properly shaping the climbing gaffs?
• What practice reduces rope snagging and tangling during a lead climb?
• If the red warning core of the WPFR straps is showing, what should be done?
• Who is authorized to modify fall protection equipment?
• Which action is required when climbing over an obstruction?
• The statement 'The person responsible for sharpening and properly shaping the climbing gaffs is the manufacturer' is true or false.
• A guardrail system is a barrier erected to prevent employees from falling to lower levels. This statement is:
• When descending a pole, longer steps are better than shorter steps.
• To comply with OSHA's requirement that impact force of a fall shall not exceed 1,800 pounds of force, a harness should be used with a deceleration unit.
• What constitutes an appropriate self-rescue plan on a rope-climbing route?
• Which statement is consistent with safety guidelines for fall protection?
• What is the difference between natural anchors and artificial anchors, and what safety considerations apply?
• Before climbing a pole, hazards around the pole, the depth of the pole in the ground and the pole itself should be checked.
• In a multi-point anchor, what is the purpose of creating a master point?
• A system that consists of an anchorage, connectors, and body harness, and includes a lanyard/deceleration device, lifeline, or combination thereof, is called a personal fall arrest system. This statement is:
• The dorsal D-ring, pigtail D-ring, or web loop are the primary means for which type of attachment?
• To climb over an obstruction, a secondary or positioning lanyard must be used.
• An improperly sharpened gaff is safer than a gaff that has not been sharpened at all.
• During a pole cut out test, the proper procedure is to ?
• The tip of the gaff should have a spike point.
• For fall arrest, the anchor point should always be kept ? the rear fall arrest attachment
• Which weather condition increases risk due to reduced friction and control?
• When selecting protection placements, what is the difference between crack-friendly gear and edge-friendly gear?
• What are common signs of rope wear that indicate retirement, and who should consult before using?
• As a good safety habit, climbing equipment should be inspected regularly.
• Shoulder D-rings can be used for fall arrest.
• A work positioning device cannot be used while climbing step bolts on a concrete or steel pole.
• When climbing or descending a pole, weight should be supported by straightening the leg and locking the knee with each step.
• Why is it important to connect multiple pieces to a master point when building an anchor?
• Why is helmet use crucial in climbing, and when should you wear it?
• To reduce accidents on the job, the climber must develop what attitude?
• When inspecting a WPFR device, which parts should be inspected?
• What is the procedure for verifying that all gear is properly connected before starting a climb?
• Warning lines, used in warning line systems, shall be erected at least ? from the roof edge when no mechanical equipment is being used.
• How do you evaluate the stability of a natural anchor such as a tree or boulder before loading it?
• Climber shank and sleeves should be inspected for ?
• Gaffs used to prevent climber cutouts must be sharp, properly sized, and properly shaped.
• It is proper procedure to hook a snaphook to another snaphook.
• Which test must precede the drop test for fall arrest equipment?
• What is the role of communication protocols in climbing, and which vocal commands are commonly used?
• Which item is essential in a minimal first-aid or emergency kit for two climbers?
• A pole that is over 20 years old should be supported with a line truck boom or other device in case it is unstable.
• The sternal D-ring is used for fall attachment when the likely fall distance is not greater than how many feet?
• What is the proper technique for cleaning chocks and nuts after a route?
• What should be done if the WPFR fails inspection?
• Fall arrest anchor points must support a minimum of ? per attached worker and be independent of worker support.
• Which item is considered essential for a basic two-person day climb to secure belaying?
• OSHA specifies the maximum length of a lanyard to limit a fall to no greater than
• How should you store and transport climbing hardware to avoid damage?
• Who can modify equipment?
• A harness should be immediately removed from service if there are
• Guardrails top rail height should be 42 inches with a tolerance of plus or minus how many inches?
• In multi-pitch routes, belaying from above is preferred when...
• Which statement best describes side D-rings positioning?
• Describe a basic method for ascending a rope (prusik-style) in a rescue scenario.
• What is the main purpose of redundancy in climbing anchors?
• In the cut-out test, to what depth should the gaff be pushed into the pole?
• Which of the following is NOT a factor to inspect when evaluating climber gaffs?
• If hardware is bent on a harness, the Qualified Electrical Worker should
• What factors influence route finding and assessment of protection placements on a route?
• What is a key practice to protect the rope from abrasion during protection placement?
• During a self-rescue, a retreat is indicated if...
• Guardrails must withstand a downward and outward force applied near the top edge of
• Which practice helps minimize tangles during a multi-pitch climb?
• Which statement best reflects the safety stance on pole attachments in most areas?
• On a multi-pitch route with a stuck rope, what should you do to avoid losing progress?
• A work positioning system can be used to support work and may allow a fall of up to how many feet?
• Side D-rings are not intended for fall arrest.
• In multi-pitch routes, belaying from above is preferred when...
• Knots and knotholes are hazards that contribute to cutout accidents.
• If attaching a personal fall arrest system directly to a web loop, the web loop must be
• Which of the following is an acceptable fall arrest attachment point on a full-body harness?
• Which description correctly defines a personal fall arrest system?
• Which harness location is recommended for lanyard attachment?
• Beginning April 1, 2015, qualified workers must use fall protection while climbing or changing locations on poles, towers, or similar structures. This statement is:
• Is twisting a safety strap to improve grip on slippery poles recommended?
• Carrying the hand line on a breakaway hook will help eliminate the hazard of being pulled off the pole by something snagging the hand line.
• What is the best practice for communicating with a partner when approaching a potentially loose rock area?
• Should a long sleeve shirt and work gloves be worn when climbing a wood pole?
• What practices help minimize rope abrasion and protect the rope during a climb?
• What is the minimal emergency kit and first-aid considerations for a two-person climbing outing?
• The OSHA fall protection standard contains training requirements.
• What is the proper technique to move up or down a pole with each step?
• What is back-clipping and why is it dangerous?
• What should you do if you notice core damage, glazing, flat spots, or stiffness on a rope?
• Which of the following should be checked and verified before starting a climb?
• What is the difference between sport climbing protection and traditional climbing protection?
• The climber straps and pads should be inspected for ?
• How is fall factor defined and how does it influence fall energy on a climb?
• The sternal D-ring is used for fall attachment when the fall distance is not greater than 2 feet.
• When testing a natural anchor, what loading approach is recommended?
• When a pole is raked, it should be climbed on the ? side.
• Which list includes essential equipment for a basic two-person day climb on a sport route?
• How do you assess a rope for safety after a potential impact (e.g., a fall)?
• List three core practices that contribute to safe belaying.
• For fall arrest, where should the anchor point be kept relative to the rear fall arrest attachment?
• Climbers are adjustable in lengths from ?
• Climbers should be inspected for which of the following dimensions when assessing gaff fit?
• Which Leave No Trace practice is considered essential on climbing routes?
• While climbing and working on a pole, how far should the climber's knees be kept away from the pole?
• What is rope drag and what strategies reduce it on a traverse?
• Which statement about PPE is true?
• Describe proper rope management to prevent rope snagging while leading.
• What is the purpose of a friction hitch in rope rescue, and how is it typically tied around the rope?
• D-rings and snap hooks used for fall protection must have a minimum tensile strength of
• Warning lines shall be erected at least how far from the roof edge when no mechanical equipment is being used?
• The keeper/gate of the snap hook should be positioned so that it is never load bearing.
• If you have a stuck rope while rappelling, what sequence supports a controlled descent?
• Work positioning equipment must meet the electric arc exposure requirements. This statement is:
• If a hazard cannot be removed from a pole that is about to be climbed, one should ? .
• The cleat must be present in the WPFR device to work properly.
• What is the function of a cordelette in anchor-building, and how many pieces does a typical setup include?
• What is the effective stroke distance when climbing up a pole?
• When engaging the pole strap at the working position, what should be verified about the safety belt?
• Which statement best describes the primary purpose of fall protection on tall structures?
• One good climbing practice that will help avoid accidents is to practice taking extra-large steps when ascending, climbing, or descending.
• If a hazard cannot be removed from the pole, what should you do before climbing?
• The gaff is properly shaped and sharpened when it begins holding a distance of 1 inch.
• Positioning side D-rings are intended for attachment of ?
• When working from an aerial lift, what protection is required?
• When ascending a rope using a friction hitch, what is the recommended action before moving to the next ascent step?
• If your partner calls for 'take' during a belay, what should you do?
• Which signaling device is included in the minimal emergency kit?
• What should be done if the WPFR fails inspection?
• Which statement about hooking snaphooks to other snaphooks is correct?
• Which statement best reflects safety emphasis in the material?
• Which of the following is NOT a criterion for inspecting climber straps and pads?
• How should the inner strap be positioned?
• Tree branches, utility line conductors, cables, tower legs, cross bracing, and lattice work are considered lower levels by OSHA. This statement is:
• When is it appropriate to use a locking carabiner in a belay setup?
• Explain the difference between a figure-eight follow-through knot and a figure-eight on a bight, including typical applications for each.
• To ensure that a snaphook is fully engaged, a worker should?
• Fall protection is required when climbing or changing locations on which structures?
• When should a plane test be performed?
• Which option best describes the primary safety approach described to reduce accidents?
• Which statement best describes the safety guidelines for gaff use and testing?
• When attaching a WPFR device to the body belt, carabiner/snaphook gates should face which direction?
• The tip of the gaff should have a spike point.
• Which statement correctly describes edge-friendly gear compared to crack-friendly gear?
• Fall protection is required at ground level. This statement is:
• A gaff that has not been sharpened at all is safer than an improperly sharpened gaff.
• The point of the gaff should cut the pole surface at a maximum depth of two inches.
• A pole that is older than 20 years and unstable should be supported with which device?
• When using a fall arrest system, what is the maximum allowed free fall distance before arrest?
• A fall arrest attachment with a web loop must be attached to a harness with a ? or a ? .
• What is the recommended sequence for constructing a redundant multi-point anchor using multiple pieces and a cordelette?
• Which device should be used to support an unstable pole older than 20 years?
• If the hardware location is described as '3 and 9' on a clock, this indicates which sides of the pole?
• Which statement about the two types of climbing gaffs is correct?
• What device helps limit peak deceleration forces during a fall by absorbing energy?
• How do dynamic ropes differ from static ropes, and in which climbing scenarios should each be used?
• How is a rappelling setup different from a lowering setup?
• What is the purpose of locking carabiners in climbing setups, and where should they be used?
• When storing climbing hardware, why should you avoid direct sunlight?
• The WPFR device is attached to which part of the climber's gear?
• Knots and knotholes are hazards that contribute to cutout accidents because the gaffs are shaped to deal with them.
• When should you retire or replace a personal anchor system (PAS)?
• What is the standard procedure for refreshing belay commands after a pause in activity?
• Which of the following reflects fall protection equipment categories?
• To minimize the chance of injury in the event of a fall, lanyards should be kept:
• How can you reduce risk when performing a rappel around a sharp edge?
• Why is redundancy essential for both bolts and natural protection in anchor systems?
• In the safety monitor program, a competent person must be close enough to the workers to do what?
• What is the purpose of a Prusik backup on rappel and how is it used?
• If the gaff slides along the wood without digging, then the gaff is either improperly sharpened or the gaff angle is too small.
• Guardrail systems must have a rail height of
• Which trio of features are identified as primary fall arrest attachments?
• If a harness shows signs of minimal fraying, it should be discarded.
• What should be done with equipment subjected to impact loading?
• What is the minimum required load rating per attached worker for fall arrest anchor points?
• At the working position and engaging the pole strap, the Qualified Electrical Worker should always look to make sure the safety belt snap has engaged the D-ring.
• The one with the responsibility for inspecting, maintaining, and rejecting climbing equipment is the ?
• Which statement best describes traditional climbing protection?
• A hitchhiking method should be used to climb with a WPFR device.
• What is the purpose of a master point in anchor systems?
• Most areas have laws that prohibit attachments on a pole such as clotheslines and signs that are not part of their structure design.
• Qualified Electrical Workers are allowed to work out of the secondary lanyard if the free fall distance is limited to how many feet?
• How does weather impact climbing safety, and what weather indicators should you monitor?
• What component must be present in the WPFR device to function properly?
• When selecting equipment, the Qualified Electrical Worker should base the selection on:
• What are two common belay device types used in sport climbing?
• The rotted surface on a pole is not a hazard because the gaffs are designed to penetrate beyond the rot.
• The inner strap accommodates for ?
• Which practice protects a rope when rappelling near a sharp edge?
• If the pole were a clock, where should the WPFR device hardware be placed?
• Climbing gaffs are available in two types, solid and ?
• Which factors should you consider when evaluating anchors for a route?
• How do bolts as anchors compare to natural protection in terms of reliability and maintenance?
• Where should lanyards be attached on harnesses?
• What is a backup friction hitch and when is it used on rappel?
• Before loading anchor slings or runners, what should you inspect and test?
• Belaying from below on multi-pitch routes is advantageous because...
• In a fall scenario, what are the main priorities for both the climber and belayer?
• The keeper/gate of the snap hook should be positioned so that it is never load bearing.
• The suspension bridge is used for which purpose?
• Which items should be checked before climbing a pole?
• Which setting best describes the primary use of a cordelette in anchor-building?
• What is the first action to take when you notice a belay device is not functioning correctly?
• What is the OSHA specified maximum length a worker can fall while using a lanyard?
• Why is it important to maintain a safe stance and stable posture while belaying?
• Climbers should not be worn when working on the ground or riding in a vehicle.